inquiry
Leave Your Message
Nm, Tex, Denier: Yarn Count Conversion Chart for Buyers
Product News

Nm, Tex, Denier: Yarn Count Conversion Chart for Buyers

2026-10-29

Home  /  Pure Cashmere  /  Yarn Count Guide

Cone of 3/68nm 100% cashmere worsted yarn in a pale pink colour with a knitted swatch of the same yarn behind it

Buyer’s Guide  ·  Yarn Counts & Sourcing

Nm, Tex, Denier: Yarn Count Conversion Chart for Buyers

The same yarn is quoted in metric count, Tex, denier and the English cotton count. A cross-system conversion chart for buyers, with the ply notation explained and a purchase order checklist.

The count belongs on the product page in the mill’s own notation, beside the knitting gauge it is built for: 3/68nm 100% cashmere worsted, 14/16gg, 1 end.

TL;DR — The Short Answer

  1. Three systems describe the same yarn with three different habits. Nm counts metres per gram, Tex counts grams per 1,000 m, denier counts grams per 9,000 m, and the English cotton count counts yards per pound. The arithmetic between them is fixed; what varies is which one each side of the table is used to.
  2. The ply notation is where bids get misread. 2/120nm is a 60 Nm yarn, not a 120 Nm yarn and not a 240 Nm yarn: divide the number after the slash by the number in front of it.
  3. Convert, then round once. Denier is quoted in whole numbers, Tex in multiples of about five, the cotton count in half steps. Rounding before converting is how a 14 Nm yarn quietly becomes a 645 denier yarn in the paperwork.
  4. Write the count the way the mill writes it. Notation, effective count, ply, composition, colourway and the test method all belong in the purchase order, because a count without a method is a number nobody can defend at the goods-in check.

Three Systems · Nm / Tex / Denier / Ne

Three systems, three different questions

A buyer comparing a cashmere quotation against a silk quotation is usually not comparing two prices; they are comparing two numbering systems that mean the same thing. Spinners in China quote in metric count, a silk buyer in Europe or Japan thinks in denier, a fabric mill thinks in Tex, and a cotton buyer thinks in the English cotton count. Each is a legitimate way to express mass per unit length, and each becomes a source of confusion the moment a quotation crosses a system boundary.

This guide uses our own published product data to make the conversion concrete: the fine count range on our pure cashmere yarns page, and the high-count 2/120nm 100% silk knitting yarn, which is the worked example that follows. Nothing here needs a spreadsheet: it needs the right notation, one division, and a table you can print.

Metric count, written Nm, asks how many metres you get from one gram. It is the native language of the spinning mill, and it scales intuitively: a higher Nm is a finer yarn, because more metres fit into the same mass. Our published cashmere range runs from chunky two-ply through 2/26nm and 2/28nm baby cashmere up to 3/68nm.

Tex asks the opposite question: how many grams are in 1,000 metres. It is the unit that fabric and knitting mills use, and it runs the other way, so a higher Tex is a heavier yarn. Tex is simply 1,000 divided by Nm, which makes it the easiest of the four to convert and the easiest to get wrong when the direction of thinking is reversed.

Denier asks how many grams are in 9,000 metres, and it is the unit of the silk and fine-denier world. It is 9,000 divided by Nm. Denier feels intuitive because 9,000 metres of one-denier yarn weighs one gram, so 150 denier weighs 150 grams over that length.

The English cotton count, written Ne, asks how many yards of yarn there are in one pound, and it is roughly 590.5 divided by Nm. It survives in cotton and some knitted-fabric buying, and it is the one most likely to be misread by somebody who has only worked in metric.

One practical point before any conversion: all four describe the yarn as it is, under a defined test method. Because a count is a measured mass per length, so the method that produced it is part of the number, and ISO 12947-1 and ISO 12947-2 set out how mass per unit length is determined for yarn from skeins and from cones respectively. The standard a supplier names in the order matters as much as the figure.

Ply Notation · 2/120nm Explained

The ply notation is where a bid gets misread

Our published 2/120nm silk knitting yarn is the clearest example of the notation, because it looks like two numbers and behaves like one. Read it as: two plies, each 120 Nm, twisted together. The finished yarn therefore has an effective count of 120 divided by 2, which is 60 Nm. From there the other systems follow in a single step: 1,000 divided by 60 gives 16.7 Tex, 9,000 divided by 60 gives 150 denier, and 590.5 divided by 60 gives a cotton count of 9.8.

Two readings of that same string go wrong in practice. The first is reading it as 120 Nm because the 120 is the bigger number, which overstates the fineness by a factor of two. The second is reading the 2 as a multiplier and arriving at 240 Nm, which treats a two-ply yarn as if it were a finer single yarn. Neither reading survives a physical check, and a physical check is cheap: ask for the count per the mill’s own method and compare it with the mass of a known length.

There is a related trap in descriptions that do not use the fraction at all. Our published cashmere entries pair counts with machine gauges and construction in words: 3/68nm as 100% cashmere worsted at 14/16gg 1 end, 2/28nm baby cashmere at 12gg 1 end, and the 2/120nm silk at 18gg 1 end. Where a count is written in one system and a gauge in another, because a gauge is a machine setting and a count is a property of the yarn, so neither converts into the other without the yarn in front of you.

Cross-System Chart · Reference Table

The cross-system chart

Here is the chart to keep next to the order form. The left-hand column uses the notation as it is written in the mill’s own catalogue, including the plies; the effective count is that number divided by the ply count; and the remaining columns are the same yarn expressed in the other three systems.

As written Effective Nm Tex (g/1000 m) Denier (g/9000 m) Ne (yd/lb) Where it appears
2/120nm 60 16.7 150 9.8 100% silk worsted, 18gg 1 end
3/68nm 22.7 44.1 397 26.1 100% cashmere worsted, 14/16gg 1 end
2/48nm 24 41.7 375 24.6 100% cashmere worsted
2/36nm 18 55.6 500 32.8 100% cashmere
2/28nm 14 71.4 643 42.2 100% baby cashmere, 12gg 1 end
2/26nm 13 76.9 692 45.4 100% cashmere
30 Nm 30 33.3 300 19.7 reference row, arithmetic only
20 Nm 20 50 450 29.5 reference row, arithmetic only
10 Nm 10 100 900 59.1 reference row, arithmetic only

Read down the Tex column: double the Nm and the Tex roughly halves. Read across a row and the same yarn appears in the language of a mill, a fabric buyer, a silk buyer and a cotton buyer, which is the point of the table.

Two habits make the table reliable. Round once, at the end, in the unit the other side will use: denier to whole numbers, Tex to the nearest five, the cotton count to the nearest half. And state the source system in the quotation, so nobody has to infer from a decimal. Because a count quoted as 76.9 Tex looks like a precision claim, while the same yarn quoted as 13 Nm is a count a spinner recognises and can reproduce, so naming the native system protects both sides from rounding arguments later.

Cone of 3/68nm 100% cashmere worsted yarn with knitted swatch
3/68nm 100% cashmere worsted, 14/16gg, 1 end — the count in the mill’s own notation, beside the gauge it was built for.

Fine-Count Range · Construction Choice

What the fine-count cashmere range shows

Look at the published cashmere range as a set and the count becomes a construction choice rather than a number. The entries run from chunky two-ply through 2/36nm, 2/28nm baby cashmere, 2/26nm and 2/48nm up to 3/68nm worsted, and the gauge changes with them: 12gg for the baby cashmere, 14/16gg for the 3/68nm, 18gg for the fine silk. Both are fine by metric count, but they are built for different machines, which is why the gauge belongs next to the count.

The same applies to the blend lines on the same category tree. Cashmere with wool, with silk, with cotton, with linen, plus recycled and antibacterial cashmere and the fancy TOPLINE range, all sit at counts chosen for the end use. Because the count is the property you convert and the fibre blend is the property you cannot convert, so a buyer who compares two quotations has to fix the count first and the blend second, otherwise the comparison is between two different products.

Purchase Order · Six Things

Writing the count into a purchase order

When a count travels from a catalogue into a contract, six things have to travel with it or it stops meaning anything.

The first is the notation exactly as written, including the ply, because “2/26nm” and “26 Nm” are different orders. The second is the effective count in the mill’s system, so that the arithmetic can be checked by either side. The third is the composition, with fibre content determined and declared by a method; ISO 1833-1 sets out the general principles for the quantitative analysis of fibre mixtures, which is how a cashmere blend is quantified rather than described. The fourth is the colourway and its dyeing route, because the published minimum order quantities on our own pages are set per colour and differ between stock-supported shades, yarn-dyed shades and top-dyed shades, so the same count in a different colourway is a different order. The fifth is the test method, whether that is the skein-based or cone-based determination. The sixth is the packaging and the delivery form, because a count verified on a cone is not automatically verified on a hank.

One more line belongs there if you buy from more than one mill: because the tolerance is written in the same unit as the count, so a tolerance quoted in Tex cannot be applied to a count quoted in Nm without converting it first, and that is the quietest source of disputes in the whole chain.

Pre-Order · Three Conversions

Three conversions to run before the order goes out

Before a purchase order leaves, three conversions earn their place.

The first is into the system your mill quotes in. If your purchasing is in denier and the supplier works in Nm, convert once and put both numbers in the order, so that neither side is translating during production.

The second is into the machine setting. Convert the count into the count that the gauge you intend to knit on expects, and check it against the yarn in hand. Published entries such as 2/28nm baby cashmere at 12gg, 3/68nm worsted at 14/16gg and 2/120nm silk at 18gg show the pairing in use, and a buyer who has the count but not the pairing will discover the gap at the machine rather than at the order.

The third is into a comparable commercial basis. Because yarn is bought by mass and often compared by length, and a kilogram of 13 Nm yarn is a very different length from a kilogram of 60 Nm silk, so converting the count into metres per kilogram before comparing two offers is what makes the comparison a comparison of yarn rather than of bags. For blends, keep the fibre content out of the arithmetic and compare the counts first.

FAQ · Buyer Questions

Frequently asked questions

Q.01What is 2/120nm in denier?+

150 denier. The number after the slash is the count of each ply and the number in front is the number of plies, so 2/120nm is a 60 Nm yarn. From there, 9,000 divided by 60 gives 150 denier, and 1,000 divided by 60 gives 16.7 Tex. Our published 2/120nm yarn is a 100% silk worsted on 18gg, single end.

Q.02How do I convert Nm to Tex without a calculator?+

Divide 1,000 by the Nm figure. The practical shortcut is to remember that 20 Nm is exactly 50 Tex, and that every doubling of Nm roughly halves the Tex, so 40 Nm is about 25 Tex and 80 Nm about 12.5 Tex. In a quotation, do the full division once and round to the nearest five.

Q.03When should I not convert a count at all?+

When both sides work in the same system. If your mill quotes in Nm and your product team specifies in Nm, converting adds a rounding step and a chance of disagreement without adding information. Conversion earns its place at a system boundary, or when you are comparing a cashmere quotation against a silk or cotton one, or when a specification is written in a third system.

Q.04Who is responsible if the delivered count does not match the order?+

The party that named the count and the method in the order, so the responsibility is decided before the yarn arrives rather than during the dispute. The specification should state the count, the notation, the tolerance in the same unit, the test method, and whether the check is performed on the delivered package. Where a blend is involved, the fibre content and the count are two separate declarations with two separate methods, and both need to be named.

Q.05Our machine is on a specific gauge. How do I match it to a count?+

Use the pairing the mills publish rather than deriving it: on our own pages 2/28nm baby cashmere is a 12gg 1 end yarn, 3/68nm worsted is a 14/16gg 1 end yarn and 2/120nm silk is an 18gg 1 end yarn. That pairing is the manufacturer’s recommendation for a specific machine, and it is worth more than any conversion, because the conversion tells you how fine the yarn is while the pairing tells you what it was built for.

Next Step · Count Verification

Send us your count. We’ll verify it against our published data.

Tell us the notation as written, the intended gauge, and the composition — our desk returns the cross-system conversion with the test method named.

Request a Count Check Browse Pure Cashmere

E

Ethan

Marketing Professional · Consinee Group Co., Ltd.

Ethan is a Marketing Professional at Consinee Group Co., Ltd., where he covers sustainable fibre sourcing, cashmere blend development and the company’s manufacturing and digitalisation programmes. His work on the blog focuses on what buyers need in order to specify yarn precisely — fibre content, count, gauge and certification — rather than on promotional description.

Facebook  ·  LinkedIn

Last verified: 2026-10-29 · All published yarn counts, gauges and certifications re-checked on the verification date